Acquisition Issues with GigE Camera
I'm trying to acquire signal from a STC-SC133POEHS GigE Camera from Omron Sentortech. The camera data are 1280 x 966 bayer RG8 - 40 fps.I was unable to grab images using the IMAQ-SX driver. I used the...
View ArticleClik here to view.
Problem bandwith with camera 2 basler gigE acA1300-60gm
I am using 2 aca1300-60gm basler cameras. I have some bandwidth problem, I see these 2 cameras use about 110Mbps in which my enthernet driver is up to 1Gpbs but I turn on the task manager see it...
View ArticleCannot adjust camera properties in NI-MAX
I have run into a problem where I cannot see or adjust camera properties (both GigE and USB cameras) on some computers in our lab. On 'good' computers I can adjust properties, perform a snap or grab,...
View ArticleClik here to view.
Distortion reduction
Hi, I Intend to reduce the distortion level to around 1 micron. Currently i am able to reduce it to up to 1 micron. How can i proceed. This is required for a measurement application I also obtained the...
View ArticleDraw rotated oval overlay
Hello,can anyone tell me how to draw a rotated oval overlay over an image, without having to rotate the image twice (as in...
View ArticleHow to protect icd files against unauthorized changes?
Hi all,I want to be sure no enthusiastic vision amateur makes changes to camera icd files, either via MAX or directly in the files themselves. Has anyone done this? Any ideas or suggestions?
View ArticleHas anyone interfaced a cRIO with an Intel Realsense D435i?
Hi, I know this has been done on a Windows PC using LabVIEW, but can it be done on a cRIO? Anybody know if this has been done?
View ArticleClik here to view.
Set a Coordinate System in Vision Assistant has wrong x-axis angle
I use Vision Assistant 2019, 32 bit.When I have 2 points from Find Circular Edge, I use Caliper: Line Fit, to make a line from that 2 points. And then Set Coordinate System, using angular motion mode,...
View Articletrasformatori monofase
buongiorno, desideravo sapere se è possibile simulare la prova a vuoto e in corto circuito di un trasformatore monofase con multisim. se è possibile mi potete fornire qualche esempio? vi ringrazio per...
View ArticleRunning Labview program, live video goes blank
Hi all, I am working with a code created to find the bullseye of an image using a template created from NI vision assistant. Upon starting the program, there is a live feed so that you can roughly line...
View ArticleIMAQ Convert Pixel to real world
I am attempting to convert pixel to real world, there are two steps in this process, as per my understanding there are two steps to this namely, application of camera matrix, followed by correction of...
View ArticleClik here to view.
Camera logitech don't open and disappear
I am using 3 logitech c922 camera with computer os windows 10. I have the following case where after 1 run of 3 cams hangs or disappears, my program cannot work.In case of camera loss, I checked in...
View ArticleClik here to view.
Get the coordinates in ROI
Is there any way to get the pixel coordinates in a previously found countour? I tried a few ways but it only gives the coordinates of the points of the boundaries?pixel coordinates to retrieve
View ArticleVBAI 2019 Developer Stalls
I was originally using VBAI 2015 64-bit to create and edit my inspections. I have been working on other projects and have not touched VBAI for a few months until recently. When I open the 64-bit...
View ArticleClik here to view.
not connect ISC-1781(Linux RT) by using Vision Builder 2015
Hello, I have an issue not to connect ISC-1781(Linux RT) by using Vision Builder 2015.Below is the current situation.ISC-1781 status is inspecting.I cannot connect ISC-1781 even after rebooting...
View ArticleAngle value in miute and Second format_VBAI
Dear Team, Is there any direct way to get the value of angle with hour, minute and second format to measure it precisely. Currently, I am converting into minute value using Formula function in...
View ArticleClik here to view.
Some settings in IMAQdx .icd are not saved, some are ignored when NI MAX...
I'm looking for NI to resolve these problems in NI MAX with regard to the IMAQ to IMAQdx transition: IMAQdx .icd file is missing the following attributeFrame Grabber Attributes :: Encoder Controls ::...
View ArticleReplacement for Ni PCI-1424
Is there any Pci-e framegrabber that can replace for Ni PCI-1424.I have a C27921CA-09 sensor which need a new computer so i need a new framegrabber which compatible with window 10.
View ArticleVBAI : Missing All State Diagram & Inspection Step in Runtime License
Dear All, I had an issue when one of my vision inspection station suddenly cannot run in production. After check, found that all state diagram and inspection step already missing. But, since the...
View ArticleClik here to view.
Acquiring Live Feed from Multiple Webcams
Hello, I started this post cause I can't find any solution to my problem.I have this project of using webcam as a barcode scanner on a simple power on test. The testing has 4 slots, which means it can...
View Article