how to get monitor Resolution
There two monitor connect to my PC, how to get their monitor resolution. can someone help me? Thanks!
View ArticleHow to change job in BAUMER camera VS XF M03 W 10EP
Dear All , I have 3 machines here in Brazil . I cant change any camera recipes by the IHM. My question is :How I can setup to change the cameras recipes remotely (etherne/Digital Inputs)?
View ArticleAccess h.264 encoded video data stream from USB webcam
I need help in a video communications application. In my project, I need to acquire video with a USB webcam, modulate and transmit data through some medium and then receive and demodulate and display...
View ArticlecRIO IMAQ Express help
I'm new to IMAQ so I need help with what I'm assuming are basic problems. I want to continuously stream the camera's image, but only capture a certain amount (N) when the control is pressed. Attached...
View ArticleCoutour Match - Scale range 1 direction axis
Hi,I have an application where I have to fit a contour with a template.Depending on the angle of view, this part can be bigger but only in one direction. Running the option "scale" of the match contour...
View ArticleImage Processing
The Program is running almost as intended; for some reason the outputs "New Picture 3" and "New Picture" appear as an "aqua-scale" but the intended result was a gray-scale. And I really dont know where...
View ArticleCopying Attributes to an Additional Camera
I have been using a raL4096-24gm Basler Racer GigE camera for my inspection and just recently added another one. I am setting the attributes through the Read/Write Camera Attributes step in VBAI. The...
View ArticleHelp with Get LCD ROI VI
Hey guys, this is my first time posting in the forum, so sorry in advance if I am doing something wrong. The objective of my program is the following:Given an image of a multimeter with all seven...
View ArticleAxis IP Camera with NI Vision Builder 2010?
HelloI would be very grateful if anyone can help with a problem i have?I would like to use a AXIS Companion V IP camera via a AXIS Switch from a laptop to use for vision detection. The software i am...
View ArticleCamera File Generator times out, flips back to 8 bits
We're trying to make a Camera File with the Camera File Generator (v3.0.1). Our camera is sending a stream of 16 bit pixels to a 1433 in base mode using 2 taps. We're getting an "Acquisition Timeout....
View Articletemporary connection loss recovery for GigE
Hi, I'm trying to cover all my bases for a long running application and there is a failure condition that is difficult to detect. In particular, if you trip over a cable Imaqdx will eventually detect...
View ArticleFFT on Image
I have an application that uses FFT to analyze thermal image How can I represnt the output of FFT Function MathematicallyAttached Screenshot ,vision assistant file and image file for demonstration
View ArticleAxis companion V Camera
Hello Could somebody with links to National Instruments please tell me if Axis Companion V cameras are supported? According to Axis they are not? Even though state that Axis and Basler cameras are...
View ArticleClik here to view.
Setting "Inter-packet delay" value in LabVIEW
I'm running a Basler Ace acA3800-gm, and trying to access it using IMAQdx. When I set up this particular camera in Basler Pylon Viewer, I need to change the value Transport Layer > Inter-Packet...
View ArticleFLIR usb3 camera with IMAQdx
Hello, I am using FLIR usb3 camera with NI IMAQdx. The VI is working in LabVIEW 2017 64bit, but not working in LabVIEW 2017 32bit, as attached photo, all sub VIs of IMAQdx are not located. Do I need to...
View ArticleIMAQdx Timeout Error 0xBFF6901B
Hello. I'm trying to acquire first images from my Basler acA2000-340kc camera link camera using IMAQdx. The frame grabber that i'm using is PCIE-1433. I'm using the base camera configuration and i keep...
View ArticleGrabbing images from two cameras in VBAI synchronously
My setup consists of VBAI 2015 and two Basler Racer Line Scan cameras. Originally, I had one camera in the setup which was working just fine on the VBAI side of things. The cycle between each image...
View ArticleBayer Encoder
I'd like to get some assistance in encoding an image to Bayer format. Does anybody have something I can use? If not, how can I create my own. I'd like to take an image/picture and encode it to a 10...
View ArticleLm386N-1 amplifier not working
I made this:https://easyeda.com/Basilisvirus/Op-ampsUsing Lm386N-1 amplifier.It doesnt output any sound on the output. I have managed to make it work once, now it doesnt, i dont know why. I also tried...
View ArticleClik here to view.
IMAQ Unwrap has some interpolation options disabled
I'm using 2018. I'm wondering why some of the options are disabled. I don't really need them at the moment but I thought it was odd:
View Article